creality ender 3 - Recalibrating Home-position - 3D Printing Stack …
WEB12. $\begingroup$. I got myself the Ender 3. The Home position is about 1 mm left and 2 mm in front of the front left corner. Now, the hotend center axis is 11 mm from the carrier plate with the "Mk 10" cooler mounted right onto a pair of 5 mm pegs that are part of the plate. As I want to change to an e3D v6, which has a diameter of 22 mm, I ...
creality ender 3 - Can't get bed to level properly - 3D Printing …
WEBDec 14, 2020 · Let it dry. Step 3: Verify bed level with a large square print that will cause the head to move to the outermost parts of the bed. Stop the print after a few outlines. Try to remove the print. If some areas are easier to remove than others, apply another coat of Elmer's glue to those areas.
How to improve very poor quality prints on my Ender 3
WEBApr 21, 2019 at 9:58. generic quality-improving steps, in order of impact: print at a slower speed. print with a smaller layer height. cut down on any breeze while printing. reduce printer shaking/vibration with weights/braces. reduce spool friction with baby powder or a spool feeder w/bearing.
creality ender 3 - 3D Printing Stack Exchange
WEBJun 22, 2021 · 4. What's causing this warping/lifting? The warping and lifting is caused by insufficient adhesion. This can be caused by an incorrect first layer (it is difficult to see the raft, but generally, rafts have no solid bottom, so less adhesion as there is less material), e.g. not sufficiently squished to the plate.
creality ender 3 - 3D Printing Stack Exchange
WEBAug 7, 2021 · A few weeks ago I got a thermal runaway message on my modded Ender 3 during a print, and I have not been able to get it working since then! I have tried fixing and replacing everything, and I still keep getting the message! When the printer starts/heats up, the thermistor is able to read the temperature with no problem, but when a print starts ...
creality ender 3 - 3D Printing Stack Exchange
WEBFeb 4, 2022 · $\begingroup$ @towe: Because the Ender 3's extruder is ungeared, it can handle wild speed and acceleration needed to make the impact on print speeds "not too bad". Just make sure you have non-zero E-jerk (maybe 5?) and E speed and accel limits set to something like 150-200 and 5000-10000, respectively.
How to avoid nozzle from hitting the model? - 3D Printing Stack …
WEBJun 18, 2019 · 3. When printing objects higher than approximately 8-10 cm, sometimes nozzle hits the printed model and knocks over it. After 7-8 hours of printing that's really annoying. I'm using Creality Ender 3 Pro with Ultimaker Cura.
How to fix "SD Init Fail" on Ender 3 - 3D Printing Stack Exchange
WEBApr 21, 2023 · 2. A possible fix that worked for me is to convert your SD card from GPT to MBR. Modern systems will usually initialize them in GPT, which seems to be incompatible with Creality boards. At least with my 4.2.7 board, this was the solution. And obviously, it has to be formatted in FAT32. Instructions on how to do it are available at Convert a GPT ...
creality ender 3 - 3D Printing Stack Exchange
WEBJun 1, 2022 · The 3D printer I'm using (Creality Ender 3 v2) stops printing at approximately the same height and no matter which model I try to print. When it stops, it does not go to park position or auto home, it just stops and sits on top of the print (getting stuck to it). It just started happening out of the blue, I have printed multiple things before this.
Print turns into spaghetti on Ender 3 Pro - 3D Printing Stack …
WEBJul 1, 2022 · I have an ender 3 pro which I use together with Cura. I print in PLA at 200 °C. The print bed is set to 60 °C. I use a print cooling fan at 100 %. The layer height I set to 0.2 mm, the line width 0.4 mm from the 0.4 mm nozzle. The Printing Speed is set to 30 mm/s for outer walls, 60 mm/s for inner walls, and 60 mm/s for infill.